Australian cloud for business software — built and run in Sydney since 2002

NetLeverage
NetLeverage

AirPrint: the Mac cannot find the printer

Technical article
Troubleshooting

About this article: This article is reviewed against the cited sources. This is source research, not lab validation. Check the stated versions and your own requirements before making changes.

The print dialog has no AirPrint printer, or Add Printer is empty. AirPrint needs an AirPrint model, with the Mac on the same Wi-Fi network as the printer. Apple's Mac printing page says the AirPrint protocol allows "Wi-Fi, USB, and Ethernet network access" to a printer's printing and scanning options. On a small network, discovery also needs the same IP subnet, because it uses Bonjour. The case here is the printer that never appears.

What has to be true

About AirPrint: "Connect the printer to your Wi-Fi network." "Make sure that your iPhone, iPad, Mac, or Apple Vision Pro is connected to the same Wi-Fi network as your printer." You do not install a driver for that model.

"Printers categorized as USB-only support driverless printing or scanning only from your Mac via USB connection. If your printer isn’t listed, check with the manufacturer." A USB-only model will not show up as a network AirPrint printer.

The Mac printing page, in its list for when you can't print to your AirPrint printer, says: "After turning on your printer, wait a minute or two before printing—some printers need a moment to join the network." If the printer is not in the Printer menu, Apple's steps say: "choose Add Printer to add it to your list."

Discovery is multicast. "Because multicast traffic is usually not routed across subnets, it requires Apple TV devices and AirPrint printers to be on the same IP subnet as the iPhone, iPad, and Mac devices that use them. For small networks, this approach is the norm." And: "Bonjour should be enabled on your network whenever access to Apple apps and services such as Classroom, AirPlay, and AirPrint are wanted. If Bonjour is misconfigured or blocked, services are not discoverable using this method."

Likely causes

Cause What you see How to confirm
Different Wi-Fi networks The list is empty; the printer shows another network name About AirPrint: same Wi-Fi network
Different subnet, or Bonjour blocked ippfind is empty on the Mac and shows the printer on a computer on the printer's own network Same IP subnet; Bonjour blocked means not discoverable
Still joining Empty for the first minute after power on "wait a minute or two"
USB-only model Cable printing works; the network list stays empty USB-only is USB only

Prove the cause before changing anything

1. Compare network names. The printer and the Mac must be on the same Wi-Fi. This check changes nothing.

2. On the Mac, in Terminal. Apple's AirPrint payload page says: "In Terminal, enter ippfind, then press Return." Its instructions are for a computer connected "to the local network where the AirPrint printer is located", so the Mac's own result is a clue, not proof.

ippfind

The page shows output such as ipp://myprinter.local.:631/ipp/port1 and says: "In this example, myprinter.local is the name of a printer and /ipp/port1 is its resource path." Apple's AirPrint payload page does not say what an empty result means.

3. If you got a name, Apple's page says to run ping with the printer's name in place of myprinter.local, and to press Control-C to stop it:

ping myprinter.local

The page's sample reply is 64 bytes from 10.50.25.21:…, and it says 10.50.25.21 is the printer's IP address. Write the address and the resource path into a new note, printer-address.txt.

4. If this Mac sees nothing, run ippfind on a computer connected to the printer's own network. A result there and none on the Wi-Fi Mac means the two computers do not see the same network. Apple says multicast discovery needs the same IP subnet and Bonjour not blocked, but its pages do not say that an empty result proves either. Write that computer's ippfind and ping results into printer-address.txt as in step 3.

Fix

Join the office Wi-Fi

This section applies when the printer is on a different Wi-Fi network from the Mac and the maker's USB setup is available.

To save the current state first, read the Wi-Fi network name from the printer's display or its setup page, and write it into a new note with the command below. In nano, type the name, or the word none if the printer shows no Wi-Fi name, then press Control-O, Return, and Control-X. The file is never empty.

nano printer-network-before.txt

Risk: the next steps change which Wi-Fi network the printer is joined to. A printer on a different network from the Mac stays out of the Mac's list until both are on the same one.

Use the maker's steps. Apple's USB overview is: connect USB, install the software that includes a setup assistant, join Wi-Fi with that assistant, then disconnect USB. "The printer should remain connected to the Wi-Fi network."

To undo it: run the setup assistant again with the USB connection and select the network name saved in printer-network-before.txt. If the file says none, there was no Wi-Fi name to go back to.

Add by address if the list stays empty

This section applies when printer-address.txt holds the printer's address, from the checks above.

To save the current list first, open System Settings, Printers & Scanners, read the names in the Printers list, and write them into a new note with the command below. In nano, type the names separated by commas, or the word none if the list is empty, then press Control-O, Return, and Control-X. The file is never empty.

nano printers-before.txt

Risk: the next steps add a print queue to this Mac. An entry with a wrong address never prints. Apple does not say whether jobs in that queue are kept.

In Printers & Scanners, click Add Printer, Scanner, or Fax, then add a network printer by specifying its IP address: enter the address from printer-address.txt, choose the AirPrint protocol, and leave Queue blank. Apple's Mac printing page says: "If you don’t know the queue name, try leaving it blank or ask your network administrator." Apple's pages do not say whether the resource path from ippfind belongs in that field.

To undo it: Control-click only the printer you just added, one that is not named in printers-before.txt, choose Remove Printer, then click Remove Printer to confirm. The address in printer-address.txt is enough to add it again.

Example (illustrative): ippfind on the staff Wi-Fi prints nothing. The printer's screen shows the guest SSID, another subnet, so multicast does not arrive. The administrator joins the printer to the staff SSID with the maker's setup assistant over USB. Two minutes later ippfind shows ipp://office-laser.local.:631/ipp/print. The list contains it. Nothing is added by hand.

Confirm the fix

  1. File, Print, lists the AirPrint printer, or you select the queue you added by address.
  2. A one-page test finishes.
  3. ippfind on a second Mac on that Wi-Fi shows the same name, unless you added only one Mac by address.
  4. The Mac is on the office Wi-Fi, not on the printer's setup network.

What to watch afterwards

  • A guest SSID, or a new staff SSID, hides the printer again. The rule stays: same Wi-Fi network.
  • After a power cut, wait a minute before you call it missing.
  • Apple's list for when you can't print to your AirPrint printer starts with updating macOS (Apple menu, System Settings, General, Software Update). Do that when you can install software, not while you are still proving discovery.
  • A configuration profile can also supply a printer. If it is missing, check that "there’s a network path for your computer to the printer."

Risks and limits

  • Empty ippfind does not say whether the cause is Wi-Fi, subnet, or a filter. The second computer separates those.
  • Apple's pages do not say what an empty ippfind result means.

Sources